Suntracer KNX sl
KNX Weather Station, GPS receiver, 8 shadings
KNX weather station with sensors for brightness, wind, precipitation, temperature.
€1,323.20
incl. 19% VAT, excl. shipping
Item No.:
Item No.: 70154
Item No.:
Item No.: 70154
Description
The weather stations Suntracer KNX sl for the KNX building bus system measure temperature, wind speed, brightness and recognise precipitation.
All values can be used for the control of limit dependent switching outputs. States can be linked via AND logic gates and OR logic gates. Multifunction modules change input data as required by means of calculations, querying a condition, or converting the data point type. The integrated shade control system allows intelligent sun protection control of up to 8 façades (with tracking of the slats and shadow edge) .
The compact housing accommodates the sensors, evaluation circuits and bus-coupling electronics.
Functions
- Brightness measurement (current light strength)
- GPS receiver outputting the current time and location coordinates. The weather station Suntracer KNX sl also computes the position of the sun (azimuth and elevation)
- Shade control for 8 facades with slat tracking and shadow edge tracking
- Air pressure measurement
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Precipitation detection: The sensor surface is heated, so that only drops and flakes are recognised as precipitation, but not mist or dew. When the rain or snow stops, the sensor is soon dry again and the precipitation warning ends
- Temperature measurement
- Frost protection for shading systems
- Switching outputs for all measured and computed values. Threshold values can be adjusted per parameter or via communication objects
- Weekly and calendar time switch: All time switching outputs can be used as communication objects. The weekly time switch has 24 periods. Each period can be configured either as an output or as an input. If the period is an output, then the switching time is set per parameter or per communication object. The calendar time switch has 4 periods. Two on/off switching operations, which are executed daily, can be set for each period
- Summer compensation for cooling systems. A characteristic curve matches the target temperature in the room to the external temperature and sets the minimum and maximum target temperature values
- 8 AND and 8 OR logic gates each with 4 inputs. All switching events as well as 16 logic inputs (in the form of communications objects) can be used as inputs for the logic gates. The output of each gate can be configured optionally as 1-bit or 2 x 8-bit
- 8 multi-function modules (computers) for changing the input data by calculations, by querying a condition or by converting the data point type
- Configuration is made using the KNX software ETS
Technical data
| General: | |
| Housing | plastic |
| Colour | white/translucent |
| Assembly | On-wall or pole |
| Protection class | IP44 |
| Dimensions (W x H x D) | 62mm × 75mm × 155mm |
| Worm-thread clamp | Ø 40...60 mm |
| Pole diameter | Ø 35...55 mm |
| Total weight | ≈ 90g |
| Ambient temperature | -30...+50°C |
| Storage temperature | -30...+70°C |
| Connection cable | 4-wire (KNX bus +/-, supply volt-age +/-), diameter approx. 5 mm J-Y(ST)Y, 2 × 2 × 0,8mm |
| KNX bus: | |
| Medium | TP1-256 |
| Configuration mode | S-Mode |
| Group addresses maximum | 2000 |
| Assignments maximum | 2000 |
| Communication objects | 1385 / 860 / 339 |
| Power consumption max. | 10mA |
| Duration after bus voltage restora-tion until data is received | ≈ 4 s |
| Supply: | |
| Voltage (SELV power supply unit in accordance with EN 61558) |
20...30V DC SELV |
| Current [at] | ≤ 90mA [24 V DC] |
| Sensors: | |
| Measurement range temperature | -30...+50°C |
| Measurement range wind | 0…35m/s |
| Measurement range pressure | 300 mbar … 1100 mbar |
| Measurement range brightness | 0 Lux … 99 000 Lux |
| Manufacturer: Elsner Elektronik GmbH Sohlengrund 16 75395 Ostelsheim Germany info@elsner-elektronik.de Made in Germany |
Scope of delivery & Accessories
- Weather station
- Connection cable approx. 10 m, with plug and connecting terminals
- Surface-mounted junction box (IP 55, for indoor use only)
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting
- Fix mounting with installation accessories
- Installation instruction (German, English, French, Italian, Spanish)
- Manual as download (German, English, French, Italian, Spanish)
- Product file as download (German, English, Fench, Italian, Spanish)
Filter by language:
RTF
ZIP
ZIP
Suntracer KNX sl Application 1.1
Status: 11.10.2023
Item No.: 70154
Languages:
de, en, fr, it, es
Suntracer KNX sl (light/basic) Installation
Status: 11.10.2023
Item No.: 70154, 70155, 70156
Languages:
de, en, fr, it, es
ZIP
Elsner Suntracer KNX sl / KNX ... sl / P04 Drawing
Status: 11.10.2023
Item No.: 30152, 30153, 30154, 30136, 70154, 70155, 70156, 70164, 70165, 71230
Languages:
de, en, fr, it, es
-
Description
-
Functions
-
Technical data
-
Scope of delivery & Accessories
-
Downloads
The weather stations Suntracer KNX sl for the KNX building bus system measure temperature, wind speed, brightness and recognise precipitation.
All values can be used for the control of limit dependent switching outputs. States can be linked via AND logic gates and OR logic gates. Multifunction modules change input data as required by means of calculations, querying a condition, or converting the data point type. The integrated shade control system allows intelligent sun protection control of up to 8 façades (with tracking of the slats and shadow edge) .
The compact housing accommodates the sensors, evaluation circuits and bus-coupling electronics.
- Brightness measurement (current light strength)
- GPS receiver outputting the current time and location coordinates. The weather station Suntracer KNX sl also computes the position of the sun (azimuth and elevation)
- Shade control for 8 facades with slat tracking and shadow edge tracking
- Air pressure measurement
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Precipitation detection: The sensor surface is heated, so that only drops and flakes are recognised as precipitation, but not mist or dew. When the rain or snow stops, the sensor is soon dry again and the precipitation warning ends
- Temperature measurement
- Frost protection for shading systems
- Switching outputs for all measured and computed values. Threshold values can be adjusted per parameter or via communication objects
- Weekly and calendar time switch: All time switching outputs can be used as communication objects. The weekly time switch has 24 periods. Each period can be configured either as an output or as an input. If the period is an output, then the switching time is set per parameter or per communication object. The calendar time switch has 4 periods. Two on/off switching operations, which are executed daily, can be set for each period
- Summer compensation for cooling systems. A characteristic curve matches the target temperature in the room to the external temperature and sets the minimum and maximum target temperature values
- 8 AND and 8 OR logic gates each with 4 inputs. All switching events as well as 16 logic inputs (in the form of communications objects) can be used as inputs for the logic gates. The output of each gate can be configured optionally as 1-bit or 2 x 8-bit
- 8 multi-function modules (computers) for changing the input data by calculations, by querying a condition or by converting the data point type
- Configuration is made using the KNX software ETS
| General: | |
| Housing | plastic |
| Colour | white/translucent |
| Assembly | On-wall or pole |
| Protection class | IP44 |
| Dimensions (W x H x D) | 62mm × 75mm × 155mm |
| Worm-thread clamp | Ø 40...60 mm |
| Pole diameter | Ø 35...55 mm |
| Total weight | ≈ 90g |
| Ambient temperature | -30...+50°C |
| Storage temperature | -30...+70°C |
| Connection cable | 4-wire (KNX bus +/-, supply volt-age +/-), diameter approx. 5 mm J-Y(ST)Y, 2 × 2 × 0,8mm |
| KNX bus: | |
| Medium | TP1-256 |
| Configuration mode | S-Mode |
| Group addresses maximum | 2000 |
| Assignments maximum | 2000 |
| Communication objects | 1385 / 860 / 339 |
| Power consumption max. | 10mA |
| Duration after bus voltage restora-tion until data is received | ≈ 4 s |
| Supply: | |
| Voltage (SELV power supply unit in accordance with EN 61558) |
20...30V DC SELV |
| Current [at] | ≤ 90mA [24 V DC] |
| Sensors: | |
| Measurement range temperature | -30...+50°C |
| Measurement range wind | 0…35m/s |
| Measurement range pressure | 300 mbar … 1100 mbar |
| Measurement range brightness | 0 Lux … 99 000 Lux |
| Manufacturer: Elsner Elektronik GmbH Sohlengrund 16 75395 Ostelsheim Germany info@elsner-elektronik.de Made in Germany |
- Weather station
- Connection cable approx. 10 m, with plug and connecting terminals
- Surface-mounted junction box (IP 55, for indoor use only)
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting
- Fix mounting with installation accessories
- Installation instruction (German, English, French, Italian, Spanish)
- Manual as download (German, English, French, Italian, Spanish)
- Product file as download (German, English, Fench, Italian, Spanish)
Filter by language:
RTF
Suntracer KNX sl Tender Specifications
Status: 11.10.2023
Item No.: 70154
Languages:
en
Suntracer KNX sl Handbuch
Status: 11.10.2023
Item No.: 70154
Languages:
de
Suntracer KNX sl Manual
Status: 11.10.2023
Item No.: 70154
Languages:
en
Suntracer KNX sl Manual
Status: 11.10.2023
Item No.: 70154
Languages:
es
Suntracer KNX sl Manuale
Status: 11.10.2023
Item No.: 70154
Languages:
it
Suntracer KNX sl Manuel
Status: 11.10.2023
Item No.: 70154
Languages:
fr
ZIP
Suntracer KNX sl Application 1.0
Status: 11.10.2023
Item No.: 70154
Languages:
de, en
ZIP
Suntracer KNX sl Application 1.1
Status: 11.10.2023
Item No.: 70154
Languages:
de, en, fr, it, es
Suntracer KNX sl (light/basic) Installation
Status: 11.10.2023
Item No.: 70154, 70155, 70156
Languages:
de, en, fr, it, es
ZIP
Elsner Suntracer KNX sl / KNX ... sl / P04 Drawing
Status: 11.10.2023
Item No.: 30152, 30153, 30154, 30136, 70154, 70155, 70156, 70164, 70165, 71230
Languages:
de, en, fr, it, es
Share Shopping Cart
×