KNX RW sl
Rain/Wind Sensor
KNX precipitation/wind sensor (rain and wind speed sensor)
€528.00
incl. 19% VAT, excl. shipping
Item No.:
Item No.: 70162
Item No.:
Item No.: 70162
Description
The Precipitation and Wind Sensor KNX RW sl for the KNX building bus system measures wind speed and detects precipitation. The wind value can be used for the control of limit dependent switching outputs. States can be linked via AND logic gates and OR logic gates. Multi-function modules change input data as required by means of calculations, querying a condition, or converting the data point type.
The compact housing of the KNX RW sl accommodates the sensors, evaluation circuits and bus-coupling electronics.
Functions
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Precipitation detection: The sensor surface is heated, so that only drops and flakes are recognised as precipitation, but not mist or dew. When the rain or snow stops, the sensor is soon dry again and the precipitation warning ends
- Switching outputs for all measured and computed values. Threshold values can be adjusted per parameter or via communication objects
- 8 AND and 8 OR logic gates, each with 4 inputs. All switching events as well as 16 logic inputs (in the form of communications objects) can be used as inputs for the logic gates. The output of each gate can be configured optionally as 1-bit or 2 x 8-bit
- 8 multi-function modules (computers) for changing the input data by calculations, by querying a condition or by converting the data point type Configuration is made using the KNX software ETS.
Technical data
| General | |
| Housing | Plastic |
| Colour | White / Translucent |
| Assembly | On-wall or pole |
| Protection class | IP 44 |
| Dimensions (W x H x D) | approx. 62 mm × 75 mm × 155 mm |
| Weight | Sensor with mount, approx. 90 g, Total weight including accessories, approx. 280 g |
| Ambient temperature | -30…+50°C |
| Storage temperature | -30…+70°C |
| KNX bus | |
| Medium | TP1-256 |
| Configuration mode | S-Mode |
| Group addresses | max. 2000 |
| Assignments | max. 2000 |
| Communication objects | 180 |
| Power consumption | max. 10 mA |
| Data output | KNX +/- |
| Connection KNX plug terminals | 0.6…0.8 mm² s |
| Stripping length | 5 mm |
| Duration after bus voltage restoration until data is received | approx. 4 s |
| Supply | |
| Auxiliary supply | 20...30 V DC |
| Auxiliary current | at 24V DC: max. 90 mA |
| Sensors | |
| Measurement range wind sensor | 0 m/s … 35 m/s |
| Manufacturer: Elsner Elektronik GmbH Sohlengrund 16 75395 Ostelsheim Germany info@elsner-elektronik.de Made in Germany |
Scope of delivery & Accessories
- Sensor
- Connection cable approx. 3 m, with plug
- Surface-mounted junction box (IP 55)
- Worm drive hose clip for pole mounting (Ø 35-55 mm)
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting.
- Data sheet with installation instruction (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download
Filter by language:
RTF
KNX W, KNX RW, KNX W sl, KNX RW sl, KNX LW sl Tender Specifications
Status: 11.10.2023
Item No.: 70129, 70119, 70123, 70158, 70162, 70164
Languages:
en
ZIP
ZIP
-
Description
-
Functions
-
Technical data
-
Scope of delivery & Accessories
-
Downloads
The Precipitation and Wind Sensor KNX RW sl for the KNX building bus system measures wind speed and detects precipitation. The wind value can be used for the control of limit dependent switching outputs. States can be linked via AND logic gates and OR logic gates. Multi-function modules change input data as required by means of calculations, querying a condition, or converting the data point type.
The compact housing of the KNX RW sl accommodates the sensors, evaluation circuits and bus-coupling electronics.
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Precipitation detection: The sensor surface is heated, so that only drops and flakes are recognised as precipitation, but not mist or dew. When the rain or snow stops, the sensor is soon dry again and the precipitation warning ends
- Switching outputs for all measured and computed values. Threshold values can be adjusted per parameter or via communication objects
- 8 AND and 8 OR logic gates, each with 4 inputs. All switching events as well as 16 logic inputs (in the form of communications objects) can be used as inputs for the logic gates. The output of each gate can be configured optionally as 1-bit or 2 x 8-bit
- 8 multi-function modules (computers) for changing the input data by calculations, by querying a condition or by converting the data point type Configuration is made using the KNX software ETS.
| General | |
| Housing | Plastic |
| Colour | White / Translucent |
| Assembly | On-wall or pole |
| Protection class | IP 44 |
| Dimensions (W x H x D) | approx. 62 mm × 75 mm × 155 mm |
| Weight | Sensor with mount, approx. 90 g, Total weight including accessories, approx. 280 g |
| Ambient temperature | -30…+50°C |
| Storage temperature | -30…+70°C |
| KNX bus | |
| Medium | TP1-256 |
| Configuration mode | S-Mode |
| Group addresses | max. 2000 |
| Assignments | max. 2000 |
| Communication objects | 180 |
| Power consumption | max. 10 mA |
| Data output | KNX +/- |
| Connection KNX plug terminals | 0.6…0.8 mm² s |
| Stripping length | 5 mm |
| Duration after bus voltage restoration until data is received | approx. 4 s |
| Supply | |
| Auxiliary supply | 20...30 V DC |
| Auxiliary current | at 24V DC: max. 90 mA |
| Sensors | |
| Measurement range wind sensor | 0 m/s … 35 m/s |
| Manufacturer: Elsner Elektronik GmbH Sohlengrund 16 75395 Ostelsheim Germany info@elsner-elektronik.de Made in Germany |
- Sensor
- Connection cable approx. 3 m, with plug
- Surface-mounted junction box (IP 55)
- Worm drive hose clip for pole mounting (Ø 35-55 mm)
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting.
- Data sheet with installation instruction (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download
Filter by language:
RTF
KNX W, KNX RW, KNX W sl, KNX RW sl, KNX LW sl Tender Specifications
Status: 11.10.2023
Item No.: 70129, 70119, 70123, 70158, 70162, 70164
Languages:
en
ZIP
KNX RW sl Application 1.0
Status: 11.10.2023
Item No.: 70162
Languages:
de, en, fr, it, es
ZIP
KNX RW sl Application 1.1
Status: 11.10.2023
Item No.: 70162
Languages:
de, en, fr, it, es
KNX RW sl Handbuch
Status: 11.10.2023
Item No.: 70162
Languages:
de
KNX RW sl Installation
Status: 11.10.2023
Item No.: 70162
Languages:
de, en, fr, it, es
KNX RW sl Manual
Status: 11.10.2023
Item No.: 70162
Languages:
en
KNX RW sl Manual
Status: 11.10.2023
Item No.: 70162
Languages:
es
KNX RW sl Manuale
Status: 11.10.2023
Item No.: 70162
Languages:
it
KNX RW sl Manuel
Status: 11.10.2023
Item No.: 70162
Languages:
fr
Share Shopping Cart
×