Suntracer KNX basic 20...30 V DC
Weather Station
Sensor for brightness, wind, precipitation, temperature. With logic gates
The Weather Station Suntracer KNX basic perceives temperature, wind speed, brightness and precipitation. All data may be used for the control of switching outputs which depend on threshold values. The states may be linked by means of AND and OR logic gates.
The compact housing of Suntracer KNX basic stores the sensor system, the evaluation electronics and the electronics of the bus connection.
- Brightness measurement: The current light intensity is measured by means of a sensor
- Wind measurement: The measurement of wind speed is accomplished electronically and thus noiseless and reliable even in case of hail, snow and minus temperature. Air swirls and up-draught in the radius of the weather station are collected, too
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, a fault can be output. The wind measured value is output with the maximum measured value of 35 m/s and all wind threshold values below this value become active
- Precipitation perception: The surface of the sensor is heated so that only drops and flakes are recognised as precipitation but not fog or dew. If it stops raining or snowing, the sensor dries quickly and the precipitation message ends
- Temperature measurement
- Threshold values can be adjusted per parameter or via communication objects
- 8 AND and 8 OR logic gates with each 4 inputs. Every switching incident as well as 8 logic inputs (in the form of communication objects) may be used as inputs for the logic gates. The output of each gate may optionally be configured as 1 bit or 2 x 8 bits
- Configuration is accomplished by means of the KNX software ETS
Housing | Plastic material |
Colour | White / translucent |
Mounting | On-wall |
Degree of protection | IP 44 |
Dimensions | approx. 96 × 77 × 118 (W × H × D, mm) |
Weight | approx. 170g |
Ambient temperature | Operation -30…+50°C, storage -30…+70°C |
Operating voltage | 20...30 V DC. An appropriate power supply unit can be obtained from Elsner Elektronik. |
Current | max. 100 mA Residual ripple: 10% |
Data output | KNX +/- bus terminal plug |
Group addresses | max. 254 |
Allocations | max. 255 |
Communication objects | 109 |
Heating rain sensor | approx. 1.2 W |
Measurement range temperature | -40…+80°C |
Measurement range wind | 0…35 m/s |
Measurement range brightness | 0…150,000 lux |
- Weather station
- 2x stainless steel installation band for pole installation
- Manual with installation instructions (German, English, French, Italian, Spanish)
- Product file VD as download (German, English, Fench, Italian, Spanish)
Filter by language:
ZIP
Item No.: 3096
Languages:
RTF
Item No.: 3096
Languages:
ZIP
Item No.: 30145, 30151, 30140, 3093, 3094, 70127, 70129, 30147, 30114, 30159, 3096, 70123, 10150
Languages:
The Weather Station Suntracer KNX basic perceives temperature, wind speed, brightness and precipitation. All data may be used for the control of switching outputs which depend on threshold values. The states may be linked by means of AND and OR logic gates.
The compact housing of Suntracer KNX basic stores the sensor system, the evaluation electronics and the electronics of the bus connection.
- Brightness measurement: The current light intensity is measured by means of a sensor
- Wind measurement: The measurement of wind speed is accomplished electronically and thus noiseless and reliable even in case of hail, snow and minus temperature. Air swirls and up-draught in the radius of the weather station are collected, too
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, a fault can be output. The wind measured value is output with the maximum measured value of 35 m/s and all wind threshold values below this value become active
- Precipitation perception: The surface of the sensor is heated so that only drops and flakes are recognised as precipitation but not fog or dew. If it stops raining or snowing, the sensor dries quickly and the precipitation message ends
- Temperature measurement
- Threshold values can be adjusted per parameter or via communication objects
- 8 AND and 8 OR logic gates with each 4 inputs. Every switching incident as well as 8 logic inputs (in the form of communication objects) may be used as inputs for the logic gates. The output of each gate may optionally be configured as 1 bit or 2 x 8 bits
- Configuration is accomplished by means of the KNX software ETS
Housing | Plastic material |
Colour | White / translucent |
Mounting | On-wall |
Degree of protection | IP 44 |
Dimensions | approx. 96 × 77 × 118 (W × H × D, mm) |
Weight | approx. 170g |
Ambient temperature | Operation -30…+50°C, storage -30…+70°C |
Operating voltage | 20...30 V DC. An appropriate power supply unit can be obtained from Elsner Elektronik. |
Current | max. 100 mA Residual ripple: 10% |
Data output | KNX +/- bus terminal plug |
Group addresses | max. 254 |
Allocations | max. 255 |
Communication objects | 109 |
Heating rain sensor | approx. 1.2 W |
Measurement range temperature | -40…+80°C |
Measurement range wind | 0…35 m/s |
Measurement range brightness | 0…150,000 lux |
- Weather station
- 2x stainless steel installation band for pole installation
- Manual with installation instructions (German, English, French, Italian, Spanish)
- Product file VD as download (German, English, Fench, Italian, Spanish)
Filter by language:
ZIP
Item No.: 3096
Languages:
RTF
Item No.: 3096
Languages:
Item No.: 3096
Languages:
Item No.: 3096
Languages:
Item No.: 3096
Languages:
Item No.: 3096
Languages:
Item No.: 3096
Languages:
Item No.: 3096
Languages:
ZIP
Item No.: 30145, 30151, 30140, 3093, 3094, 70127, 70129, 30147, 30114, 30159, 3096, 70123, 10150
Languages: