Intra-Sewi KNX T
Built-in Type Temperature Sensor
KNX-wall/ceiling sensor. Temperature sensor with logic gates
Highlights
-
-
Sensor with room thermostat
-
-
Awarded design with glass surface
- - For wall and ceiling installation
The Sensors Intra-Sewi KNX T for the KNX building bus system measure the ambient temperature. Via the bus, the indoor sensors can receive external values of temperature and process them further with their own data to a total value (mixed value, e.g. room average). The measurement values can be used for the control of limit-dependent switching outputs. States can be linked via AND logic gates and OR logic gates. In addition, an integrated actuating variable comparator can compare and output variables that were received via communication objects. An integrated PI-controller controls a heating/cooling (according to temperature).
Models:
N° 70660 Intra-Sewi KNX T Built-in Type Sensor for Temperature/Humidity (white)
N° 70665 Intra-Sewi KNX T Built-in Type Sensor for Temperature/Humidity (black)
- Measuring the temperature, with mixed value calculation. The share of
internal measurement value and external value can be set as a percentage - Threshold values can be adjusted per parameter or via communication
objects - PI-controller for heating (one or two-stage) and cooling (one or twostage)
according to temperature. Regulation according to separate setpoints
or basic setpoint temperature - 4 AND and 4 OR logic gates, each with 4 inputs. All switching events as
well as 16 logic inputs (in the form of communications objects) can be used
as inputs for the logic gates. The output of each gate can be configured
optionally as 1-bit or 2 x 8-bit - 2 actuation variable comparators to output minimum, maximum or
average values. 5 inputs each for values received via communication objects
Configuration is made using the KNX software ETS
General: | |
Housing | Plastic, glass |
Colour | • similar to signal white RAL 9003 • similar to jet black RAL 9005 |
Assembly | built-in, in false ceiling or connector socket |
Dimensions Ø x height above wall | approx. 80 mm x approx. 5 mm height in wall (installation) approx. 31 mm (incl. clamps) |
Degree of protection | IP 30 |
Weight | approx. 50 g |
Ambient temperature | -20…+60°C |
Ambient humidity | 5...95% RH, non-condensing |
Storage temperature | -30…+70°C |
KNX bus: | |
KNX medium | TP1-256 |
Configuration mode | S-Mode |
Group addresses | max. 254 |
Assignments | max. 254 |
Communication objects | 129 |
Nominal voltage KNX | 30 V DC SELV |
Power consumption KNX | max. 10 mA |
Connection | KNX plug terminals |
Duration after bus voltage restoration until data is received | approx. 5 seconds |
Sensor: | |
Measurement range | -20°C … +60°C |
- Sensor
- Pre-assembled clamps for false ceiling installation
- Support ring for connector socket installation
- Installation instructions (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download
- Product file (German, English, French, Italian, Spanish) as download
For socket installation you will need in addition (not supplied):
- Socket Ø 60 mm, 42 mm deep
Filter by language:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
ZIP
Item No.: 70660, 70665
Languages:
RTF
Item No.: 70660, 70665, 70666, 70661
Languages:
The Sensors Intra-Sewi KNX T for the KNX building bus system measure the ambient temperature. Via the bus, the indoor sensors can receive external values of temperature and process them further with their own data to a total value (mixed value, e.g. room average). The measurement values can be used for the control of limit-dependent switching outputs. States can be linked via AND logic gates and OR logic gates. In addition, an integrated actuating variable comparator can compare and output variables that were received via communication objects. An integrated PI-controller controls a heating/cooling (according to temperature).
Models:
N° 70660 Intra-Sewi KNX T Built-in Type Sensor for Temperature/Humidity (white)
N° 70665 Intra-Sewi KNX T Built-in Type Sensor for Temperature/Humidity (black)
- Measuring the temperature, with mixed value calculation. The share of
internal measurement value and external value can be set as a percentage - Threshold values can be adjusted per parameter or via communication
objects - PI-controller for heating (one or two-stage) and cooling (one or twostage)
according to temperature. Regulation according to separate setpoints
or basic setpoint temperature - 4 AND and 4 OR logic gates, each with 4 inputs. All switching events as
well as 16 logic inputs (in the form of communications objects) can be used
as inputs for the logic gates. The output of each gate can be configured
optionally as 1-bit or 2 x 8-bit - 2 actuation variable comparators to output minimum, maximum or
average values. 5 inputs each for values received via communication objects
Configuration is made using the KNX software ETS
General: | |
Housing | Plastic, glass |
Colour | • similar to signal white RAL 9003 • similar to jet black RAL 9005 |
Assembly | built-in, in false ceiling or connector socket |
Dimensions Ø x height above wall | approx. 80 mm x approx. 5 mm height in wall (installation) approx. 31 mm (incl. clamps) |
Degree of protection | IP 30 |
Weight | approx. 50 g |
Ambient temperature | -20…+60°C |
Ambient humidity | 5...95% RH, non-condensing |
Storage temperature | -30…+70°C |
KNX bus: | |
KNX medium | TP1-256 |
Configuration mode | S-Mode |
Group addresses | max. 254 |
Assignments | max. 254 |
Communication objects | 129 |
Nominal voltage KNX | 30 V DC SELV |
Power consumption KNX | max. 10 mA |
Connection | KNX plug terminals |
Duration after bus voltage restoration until data is received | approx. 5 seconds |
Sensor: | |
Measurement range | -20°C … +60°C |
- Sensor
- Pre-assembled clamps for false ceiling installation
- Support ring for connector socket installation
- Installation instructions (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download
- Product file (German, English, French, Italian, Spanish) as download
For socket installation you will need in addition (not supplied):
- Socket Ø 60 mm, 42 mm deep
Filter by language:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
Item No.: 70665, 70666, 70669
Languages:
ZIP
Item No.: 70660, 70665
Languages:
RTF
Item No.: 70660, 70665, 70666, 70661
Languages: