KNX LW sl
Brightness/wind sensor
KNX brightness/wind sensor (sun/brightness and wind speed sensor)
The Brightness and Wind Sensor KNX LW sl for the KNX building bus system measures brightness and wind speed.
All values can be used for the control of limit dependent switching outputs. States can be linked via AND logic gates and OR logic gates. Multi-function modules change input data as required by means of calculations, querying a condition, or converting the data point type.
The compact housing of the KNX LW sl accommodates the sensors, evaluation circuits and bus-coupling electronics.
- Brightness: The current light intensity is measured by a sensor
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Switching outputs for all measured and computed values. Threshold values can be adjusted per parameter or via communication objects
- 8 AND and 8 OR logic gates, each with 4 inputs. All switching events as well as 16 logic inputs (in the form of communications objects) can be used as inputs for the logic gates. The output of each gate can be configured optionally as 1-bit or 2 x 8-bit
- 8 multi-function modules (computers) for changing the input data by calculations, by querying a condition or by converting the data point type. Configuration is made using the KNX software ETS.
General | |
Housing | Plastic |
Colour | White / Translucent |
Assembly | On-wall or pole |
Protection class | IP 44 |
Dimensions (W x H x D) | approx. 62 mm × 75 mm × 155 mm |
Weight | Sensor with mount, approx. 90 g, Total weight including accessories, approx. 280 g |
Ambient temperature | -30…+50°C |
Storage temperature | -30…+70°C |
KNX bus | |
Medium | TP1-256 |
Configuration mode | S-Mode |
Group addresses | max. 2000 |
Assignments | max. 2000 |
Communication objects | 301 |
Power consumption | max. 10 mA |
Data output | KNX +/- |
Connection KNX plug terminals | 0.6…0.8 mm² s |
Stripping length | 5 mm |
Duration after bus voltage restoration until data is received | approx. 4 s |
Supply | |
Auxiliary supply | 20...30 V DC |
Auxiliary current | at 24V DC: max. 90 mA |
Sensors | |
Measurement range wind sensor | 0 m/s … 35 m/s |
Measurement range brightness sensor | 0 lux … 99,000 lux |
- Sensor
- Connection cable approx. 3 m, with plug
- Surface-mounted junction box (IP 55)
- Worm-thread clamp Ø 40-60 mm, suitable for pole Ø 35-55 mm
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting.
- Data sheet with installation instruction (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download
Filter by language:
RTF
Item No.: 70129, 70119, 70123, 70158, 70162, 70164
Languages:
ZIP
ZIP
ZIP
Item No.: 30152, 30153, 30154, 30136, 70154, 70155, 70156, 70164, 70165, 71230
Languages:
The Brightness and Wind Sensor KNX LW sl for the KNX building bus system measures brightness and wind speed.
All values can be used for the control of limit dependent switching outputs. States can be linked via AND logic gates and OR logic gates. Multi-function modules change input data as required by means of calculations, querying a condition, or converting the data point type.
The compact housing of the KNX LW sl accommodates the sensors, evaluation circuits and bus-coupling electronics.
- Brightness: The current light intensity is measured by a sensor
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Switching outputs for all measured and computed values. Threshold values can be adjusted per parameter or via communication objects
- 8 AND and 8 OR logic gates, each with 4 inputs. All switching events as well as 16 logic inputs (in the form of communications objects) can be used as inputs for the logic gates. The output of each gate can be configured optionally as 1-bit or 2 x 8-bit
- 8 multi-function modules (computers) for changing the input data by calculations, by querying a condition or by converting the data point type. Configuration is made using the KNX software ETS.
General | |
Housing | Plastic |
Colour | White / Translucent |
Assembly | On-wall or pole |
Protection class | IP 44 |
Dimensions (W x H x D) | approx. 62 mm × 75 mm × 155 mm |
Weight | Sensor with mount, approx. 90 g, Total weight including accessories, approx. 280 g |
Ambient temperature | -30…+50°C |
Storage temperature | -30…+70°C |
KNX bus | |
Medium | TP1-256 |
Configuration mode | S-Mode |
Group addresses | max. 2000 |
Assignments | max. 2000 |
Communication objects | 301 |
Power consumption | max. 10 mA |
Data output | KNX +/- |
Connection KNX plug terminals | 0.6…0.8 mm² s |
Stripping length | 5 mm |
Duration after bus voltage restoration until data is received | approx. 4 s |
Supply | |
Auxiliary supply | 20...30 V DC |
Auxiliary current | at 24V DC: max. 90 mA |
Sensors | |
Measurement range wind sensor | 0 m/s … 35 m/s |
Measurement range brightness sensor | 0 lux … 99,000 lux |
- Sensor
- Connection cable approx. 3 m, with plug
- Surface-mounted junction box (IP 55)
- Worm-thread clamp Ø 40-60 mm, suitable for pole Ø 35-55 mm
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting.
- Data sheet with installation instruction (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download
Filter by language:
RTF
Item No.: 70129, 70119, 70123, 70158, 70162, 70164
Languages:
ZIP
Item No.: 70164
Languages:
ZIP
Item No.: 70164
Languages:
Item No.: 70164
Languages:
Item No.: 70164
Languages:
Item No.: 70164
Languages:
Item No.: 70164
Languages:
Item No.: 70164
Languages:
Item No.: 70164
Languages:
ZIP
Item No.: 30152, 30153, 30154, 30136, 70154, 70155, 70156, 70164, 70165, 71230
Languages: