P04-KNX-GPS
Weather Station
KNX weather stations with sensors for brightness, wind, precipitation, temperature. Time reception via GPS
Highlights
-
-
Weather sensor/combined sensor: sun sensor, electronic wind sensor, rain sensor, thermometer, GPS receiver
- - Slim design, unobtrusive on the façade
The Weather Station P04-KNX-GPS for the KNX building bus system measures temperature, wind speed and brightness. It recognises precipitation and receives the GPS signal for time and location.
The compact housing of the P04-KNX-GPS accommodates the sensors, evaluation circuits and bus-coupling electronics.
- Brightness measurement
- GPS receiver, outputting the current time and location coordinates
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Precipitation detection: The sensor surface is heated, so that only drops and flakes are recognised as precipitation, but not mist or dew. When the rain or snow stops, the sensor is soon dry again and the precipitation warning ends
- Temperature measurement
- Configuration is made using the KNX software ETS
General: | |
Housing | plastic |
Colour | white/translucent |
Assembly | On-wall or pole |
Protection class | IP44 |
Dimensions (W x H x D) | 62mm × 75mm × 155mm |
Total weight | ≈ 90g |
Ambient temperature | -30...+50°C |
Storage temperature | -30...+70°C |
Connection cable 4-wire (KNX bus +/-, supply volt-age +/-), diameter approx. 5 mm |
J-Y(ST)Y, 2 × 2 × 0,8mm |
KNX bus: | |
Medium | TP1-256 |
Configuration mode | S-Mode |
Group addresses maximum | 2000 |
Assignments maximum | 2000 |
Communication objects | 28 |
Power consumption | ≤ 10mA |
Data output | KNX +/- |
Duration after bus voltage restora-tion until data is received | ≈ 4 s |
Supply: | |
Voltage | 20...30V DC |
Current [at] | ≤ 90mA [24 V DC] |
Sensors: | |
Measurement range temperature | -30...+50°C |
Measurement range wind | 0…35m/s |
Measurement range brightness | 0 Lux … 99000 Lux |
- Sensor
- Connection cable approx. 10 m, with plug and connecting terminals
- Surface-mounted junction box (IP 55, not weatherproof)
- Worm-thread clamp Ø 40-60 mm, suitable for pole Ø 35-55 mm
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting. Use fixing materials that are suitable for the base!
- Fix mounting with installation accessories
- Data sheet with installation instructions (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download - Product file (German, English, French, Italian, Spanish) as download
Filter by language:
ZIP
Item No.: 71230
Languages:
RTF
ZIP
Item No.: 30152, 30153, 30154, 30136, 70154, 70155, 70156, 70164, 70165, 71230
Languages:
The Weather Station P04-KNX-GPS for the KNX building bus system measures temperature, wind speed and brightness. It recognises precipitation and receives the GPS signal for time and location.
The compact housing of the P04-KNX-GPS accommodates the sensors, evaluation circuits and bus-coupling electronics.
- Brightness measurement
- GPS receiver, outputting the current time and location coordinates
- Wind measurement: The wind strength is measured electronically and thus noiselessly and reliably, even during hail, snow and sub-zero temperatures. Even turbulent air and rising winds in the vicinity of the device are recorded
- Wind sensor monitoring: If the wind measurement value changes by less than ± 0.5 m/s within 48 hours, the maximum measurement value of 35 m/s is output as a fault message. All wind alarms with a limit value below 35 m/s become active as a result
- Precipitation detection: The sensor surface is heated, so that only drops and flakes are recognised as precipitation, but not mist or dew. When the rain or snow stops, the sensor is soon dry again and the precipitation warning ends
- Temperature measurement
- Configuration is made using the KNX software ETS
General: | |
Housing | plastic |
Colour | white/translucent |
Assembly | On-wall or pole |
Protection class | IP44 |
Dimensions (W x H x D) | 62mm × 75mm × 155mm |
Total weight | ≈ 90g |
Ambient temperature | -30...+50°C |
Storage temperature | -30...+70°C |
Connection cable 4-wire (KNX bus +/-, supply volt-age +/-), diameter approx. 5 mm |
J-Y(ST)Y, 2 × 2 × 0,8mm |
KNX bus: | |
Medium | TP1-256 |
Configuration mode | S-Mode |
Group addresses maximum | 2000 |
Assignments maximum | 2000 |
Communication objects | 28 |
Power consumption | ≤ 10mA |
Data output | KNX +/- |
Duration after bus voltage restora-tion until data is received | ≈ 4 s |
Supply: | |
Voltage | 20...30V DC |
Current [at] | ≤ 90mA [24 V DC] |
Sensors: | |
Measurement range temperature | -30...+50°C |
Measurement range wind | 0…35m/s |
Measurement range brightness | 0 Lux … 99000 Lux |
- Sensor
- Connection cable approx. 10 m, with plug and connecting terminals
- Surface-mounted junction box (IP 55, not weatherproof)
- Worm-thread clamp Ø 40-60 mm, suitable for pole Ø 35-55 mm
- 4×50 mm stainless steel roundhead screws and 6×30 mm dowels for wall mounting. Use fixing materials that are suitable for the base!
- Fix mounting with installation accessories
- Data sheet with installation instructions (German, English, French, Italian, Spanish)
- Manual (German, English, French, Italian, Spanish) as download - Product file (German, English, French, Italian, Spanish) as download
Filter by language:
ZIP
Item No.: 71230
Languages:
RTF
Item No.: 71230
Languages:
Item No.: 71230
Languages:
Item No.: 71230
Languages:
Item No.: 71230
Languages:
Item No.: 71230
Languages:
Item No.: 71230
Languages:
Item No.: 71230
Languages:
ZIP
Item No.: 30152, 30153, 30154, 30136, 70154, 70155, 70156, 70164, 70165, 71230
Languages: